Filetype
Automatic video captioning is challenging due to the complex interactions in dynamic real scenes. A comprehensive system would ultimately localize and track the objects, actions and interactions present in a video and generate a description that relies on temporal localization in order to ground the visual concepts. However, most existing automatic video captioning systems map from raw video data
Resilience has become a key aspect in the design of contemporary infrastructure networks. This comes as a result of ever-increasing loads, limited physical capacity, and fast-growing levels of interconnectedness and complexity due to the recent technological advancements. The problem has motivated a considerable amount of research within the last few years, particularly focused on the dynamical as
Two 60-GHz band voltage controlled oscillators (VCOs) designed in a 28-nm ultrathin body and buried oxide fully depleted silicon on insulator (UTBB FD-SOI) CMOS process are demonstrated and compared. Both VCOs have identical cross-coupled nMOS cores and dissipate 3.15 mW from a 0.9-V supply. The first design uses a standard FET current source and achieves a figure of merit (FOM) of −181 dBc/Hz, wh
A systematic approach to the analysis and design of a class of large dynamical systems is presented. The approach allows decentralized control laws to be designed independently using only local subsystem models. Design can be conducted using standard techniques, including loopshaping based on Nyquist and Popov plots, H methods, and μ-synthesis procedures. The approach is applied to a range of netw
This paper presents the mathematical conditions and the associated design methodology of an active fault diagnosis technique for continuous-time linear systems. Given a set of faults known a priori, the system is modeled by a finite family of linear time-invariant systems, accounting for one healthy and several faulty configurations. By assuming bounded disturbances and using a residual generator,
We consider flow-inducing networks, a class of models that are well-suited to describe important biochemical systems, including the MAPK pathway and the interactions at the trans-Golgi network. A flow-inducing network is given by the interconnection of subsystems (modules), each associated with a stochastic state matrix whose entries depend on the state variables of other modules. This results in
In modern day industry, robots are indispensable for achieving high production rates and competitiveness. In small and medium scale enterprises, where the production may shift rapidly, it is vital to be able to reprogram robots quickly. Kinesthetic teaching, also known as lead-through programming (LTP), provides a fast approach for teaching a trajectory. In this approach, a trajectory is demonstra
We present a data-driven interpolation method, based on extended structure tensors. The method uses directional information, extracted from the crossline derivative of the pressure field, to interpolate both pressure field and its normal (depth) derivative. Here we focus on the interpolation of the normal derivative.
We present a data-driven method, based on extended structure tensors, that interpolates multicomponent, marine seismic data. The method is designed to interpolate pressure measurements and their normal derivatives using directional information from the crossline derivative of the pressure field.
Welding robots that use sensors to compensate for variations in their environment pose new requirements for programming systems and for controller architectures. Tracking sensors must be programmed with the geometry of the welds and the motions of the robot. The process monitoring system must be programmed with the required process tolerances and the type of weld. Finally, the controller must be pWelding robots that use sensors to compensate for variations in their environment pose new requirements for programming systems and for controller architectures. Tracking sensors must be programmed with the geometry of the welds and the motions of the robot. The process monitoring system must be programmed with the required process tolerances and the type of weld. Finally, the controller must be p
In this paper we propose an autotuning method that combines a setup for decentralized relay autotuning of two-input two-output systems with an identification method that uses short experiments to estimate up to second-ordertime-delayed systems. A small modification of the experiment gives better low-frequency excitation and improved models. The method is successfully demonstrated in simulations an
Marine seismic data are distorted by ghosts as waves propagating upwards reflect downwards from the sea surface. Ghosts appear both on the source-side as well as on the receiver-side. However, whereas the receiver-side ghost problem has been studied in detail and many different solutions have been proposed and implemented commercially, the source-side ghost problem has remained largely "unsolved"
In wavefield signal apparition, acquisition with periodic variations in source activation parameters shifts all or part of a signal cone out to, e.g., the Nyquist wavenumber, enabling perfect separation of simultaneous-source (sim-source) data below a certain temporal frequency. Cyclic convolution in the spatial frequency domain is used to generalise the signal apparition concept to the case of ap
Future district heating systems (so called 4th Generation District Heating (4GDH) systems) have to address challenges such as integration of (de)centralized renewable energy sources and storage, low system temperatures and high fluctuation of the supply temperature. This paper presents a novel framework for representing and simplifying on-grid energy systems as well as for dynamic thermo-hydraulic
The relay autotuner for PID control is based on the simple idea of investigating process dynamics by the oscillation obtained when the PID controller is replaced by a relay unction. In this paper an asymmetric relay function is used, which provides an equation for the static gain of the process. A method to find the normalized time delay is proposed and the benefits of this is discussed. Ways to f
Modern software applications are subject to uncertain operating conditions, such as dynamics in the availability of services and variations of system goals. Consequently, runtime changes cannot be ignored, but often cannot be predicted at design time. Control theory has been identified as a principled way of addressing runtime changes and it has been applied successfully to modify the structure an
Particle methods such as the particle filter and particle smoothers have proven very useful for solving challenging nonlinear estimation problems in a wide variety of fields during the last decade. However, there are still very few existing tools available to support and assist researchers and engineers in applying the vast number of methods in this field to their own problems. This paper identifi
An algorithm for high-performance path tracking for robot manipulators in the presence of model uncertainties and actuator constraints is presented. The path to be tracked is assumed given, and the nominal trajectories are computed using, for example, well-known algorithms for time-optimal path tracking. For online path tracking, the nominal, feedforward trajectories are combined with feedback in
Industrial robots typically require very structured and predictable working environments, and explicit programming, in order to perform well. Therefore, expensive and time-consuming engineering work is a major obstruction when mediating tasks to robots. This thesis presents methods that decrease the amount of engineering work required for robot programming, and increase the ability of robots to ha
